Plumbing 101: Tips for Installing a Bathtub
Plumbing 101: Tips for Installing a Bathtub
Blog Article
How do you feel about How to Install a Bathtub?
Mounting a bath tub isn't exactly rocket science, but it does require strong plumbing, woodworking, and occasionally, tiling abilities. Replacing an old tub with a brand-new one is also a reasonably tough task. If the old tub is conveniently available, the project can relocate rapidly; if you need to open a wall surface to get rid of the old bathtub as well as place the new bath tub, the task is a lot harder. In either instance, the project is within a home handyman's skills, although you will certainly need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually certified on your own for the work as well as are comfortable attempting it. Rather than hiring a contractor to take over a halfway-completed task, it is far better to think about using one before you begin. Chances are you may require a specialist plumber to make tube connections.
This write-up will assist you set up a new bath tub in your bathroom if you have actually currently acquired a brand-new bathtub and don't require to change the arrangement of your previous supply of water pipelines.
Your devices and also material list need to make up the following:
Removing Old Touches
If you need to replace old taps with brand-new ones as a part of your setup, then the first thing you ought to do is disconnect the water system. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of getting rid of the existing faucets can be fairly bothersome as a result of the limited gain access to that is often the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipes to the taps. Have a fabric prepared for the staying water that will come from the pipes. As soon as the supply pipes have been eliminated, make use of the exact same tool to loosen the nut that holds the faucets onto the bath/basin. You will need to stop the single taps from transforming during this process. As soon as the taps have actually been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Before carrying on to fit the brand-new faucets, compare the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the brand-new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly require a plastic adapter to stop damage to the thread. One end of the connector fits on the plastic tail of the faucet and the various other end supplies a link to the existing supply pipes.
If you require to fit a monobloc, after that you will certainly need lowering couplers, which links the 10mm pipe of the monobloc to the basic 15mm supply pipe.
Next, place the faucet in the placing opening in the bath/basin guaranteeing that the washers are in location in between the tap and the sink. Safeguard the faucet in position with the maker provided backnut. When the faucet is firmly in place, the supply pipes can be attached to the tails of the faucets. The faucets can either be attached by utilizing corrugated copper piping or with regular faucet connectors. The former type ought to be connected to the faucet ends initially, tightening up just by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have been connected.
Setting up the Bath tub
Making use of both wood boards under its feet, put the bathtub in the required placement. The wooden boards are practical in equally spreading out the weight of the tub over the location of the boards as opposed to concentrating all the weight onto four little points.
The next goal is to guarantee that the bathtub is leveled all round. This can be achieved by checking the level and also changing the feet on the bath tub until the level reads degree.
To install taps, fit all-time low of the furthest adaptable tap port to the appropriate supply pipeline by making a compression join; after that do the same for the various other faucet.
Switch on the water supply as well as inspect all joints and also brand-new pipework for leaks and tighten them if necessary. Fill the bathtub and also check the overflow electrical outlet and also the regular outlet for leaks.
Ultimately, fix the bathroom paneling as described in the supplier's user's manual. Tiling and securing around the tub should wait till the tub has been used at least once as this will certainly settle it right into its final placement.
Planning for the Setup
Firstly, the sustaining frame supplied with the bath needs to be fitted (if required) according to the supplier's directions. Next, fit the faucets or mixer to the bath tub. When fitting the faucet block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bathroom and the faucets. On a plastic bath, it is additionally sensible to fit a sustaining plate under the taps system to prevent strain on the bathtub.
Fit the versatile tap connectors to the bottom of the two faucets using 2 nuts and also olives (in some cases supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet hole, and afterwards pass the outlet via the hole in the bath. Utilize the nut supplied by the maker to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipeline to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Make sure you use every one of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath ought to now prepare to be suited its final position.
Tiling Around the Bathtub
In the location where the bath meets the floor tile, it is needed to seal the accompanies a silicone rubber caulking. This is essential as the fitting can relocate enough to split a rigid seal, causing the water to penetrate the wall surface in between the bathroom and the tiling, bring about issues with wetness and feasible leakages to the ceiling below.
You can select from a selection of coloured sealants to assimilate your components and fittings. They are marketed in tubes and cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill up, you can load it with spins of drenched newspaper or soft rope. Remember to constantly fill up the tub with water before sealing, to allow for the activity experienced when the bathtub remains in use. The sealer can fracture fairly very early if you do not take into consideration this movement prior to securing.
Additionally, ceramic coving or quadrant ceramic tiles can be used to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also easily readily available on the marketplace. It is advisable to fit the tiles making use of water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As a passionate reader about A Step-by-Step Guide to Installing a Bathtub, I imagined sharing that post was worth the trouble. I beg you take the opportunity to promote this entry if you enjoyed reading it. Many thanks for going through it.
Automated Marketing Report this page